C9130AXI-S Specification |
|
Software
|
Catalyst 9130AXI
• Cisco Unified Wireless Network Software Release 8.10.x or later • Cisco IOS ® XE Software Release 16.12.1 with AP Device Pack, or later |
Supported wireless LAN controllers
|
• Cisco Catalyst 9800 Series Wireless Controllers
• Cisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller |
802.11n version 2.0 (and related) capabilities
|
• 4×4 MIMO with four spatial streams
• Maximal Ratio Combining (MRC) • 802.11n and 802.11a/g • 20- and 40-MHz channels • PHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) • Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive) • 802.11 Dynamic Frequency Selection (DFS) • Cyclic Shift Diversity (CSD) support |
802.11ac
|
• 8×8 downlink MU-MIMO with eight spatial streams
• MRC • 802.11ac beamforming • 20-, 40-, 80-, and 160-MHz channels • PHY data rates up to 6.9 Gbps (160 MHz with 5 GHz) • Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) • 802.11 DFS • CSD support • WPA3 support |
802.11ax
|
• 8×8 uplink/downlink MU-MIMO with eight spatial streams
• Uplink/downlink OFDMA • TWT • BSS coloring • MRC • 802.11ax beamforming • 20-, 40-, 80-, and 160-MHz channels • PHY data rates up to 10 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) • Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) • 802.11 DFS • CSD support • WPA3 support |
Integrated antenna
|
• 2.4 GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth
• 5 GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth |
External antenna with Smart antenna connector
|
• The Cisco Catalyst 9130AXE Access Point is certified for use with antenna gains up to 13 dBi (2.4 GHz and 5 GHz)
• Cisco offers the industry’s broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios • Supports Self-Identifiable Antennas (SIA) on the Smart antenna connector • Smart antenna connector is a compact multi-RF connector with 8-DART interface • Requires the AIR-CAB002-D8-R= 2-fppt smart antenna connector when used with antennas with a RP-TNC connector • Requires the AIR-CAB003-D8-N= 3 ft smart antenna connector when used with AIR-ANT2513P4M-N= antenna |
Interfaces
|
• 1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz
• Management console port (RJ-45) • USB 2.0 at 4.5W (enabled via future software) |
Indicators
|
• Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors |
Dimensions (W x L x H)
|
• Access point (without mounting brackets):
– C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm) |
Environmental
|
Cisco Catalyst 9130AXI
• Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) • Nonoperating (storage) altitude test: 25˚C, 15,000 ft (4600 m) • Operating temperature: 32° to 122°F (0° to 50°C) • Operating humidity: 10% to 90% (noncondensing) • Operating altitude test: 40˚C, 9843 ft (3000 m) Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 8×8 to 4×4 on the 5 GHz radio, uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled. |
System memory
|
• 2048 MB DRAM
• 1024 MB flash |
Warranty | Limited lifetime hardware warranty |
Available transmit power settings
|
2.4 GHz
• 23 dBm (200 mW) • 20 dBm (100 mW) • 17 dBm (50 mW) • 14 dBm (25 mW) • 11 dBm (12.5 mW) • 8 dBm (6.25 mW) • 5 dBm (3.13 mW) • 2 dBm (1.56 mW) • -1 dBm (0.79 mW) • -4 dBm(0.39 mW) 5 GHz • 26 dBm (400 mW) • 23 dBm (200 mW) • 20 dBm (100 mW) • 17 dBm (50 mW) • 14 dBm (25 mW) • 11 dBm (12.5 mW) • 8 dBm (6.25 mW) • 5 dBm (3.13 mW) • 2 dBm (1.56 mW) • -1 dBm (0.79 mW) |
Maximum number of nonoverlapping channels
|
2.4 GHz
• 802.11b/g: – 20 MHz: 3 • 802.11n: – 20 MHz: 3 • 802.11ax: – 20 MHz: 3 5 GHz • 802.11a: – 20 MHz: 26 FCC, 16 EU • 802.11n: – 20 MHz: 26 FCC, 16 EU – 40 MHz: 12 FCC, 7 EU • 802.11ac/ax: – 20 MHz: 26 FCC, 16 EU – 40 MHz: 12 FCC, 7 EU – 80 MHz: 5 FCC, 3 EU – 160 MHz 2 FCC, 1 EU Note: This varies by regulatory domain. Refer to the product documentation for specific details for each regulatory domain. |
Compliance standards | • Safety:
– IEC 60950-1 – EN 60950-1 – UL 60950-1 – CAN/CSA-C22.2 No. 60950-1 – AS/NZS60950.1 – UL 2043 – Class III equipment • Emissions: – CISPR 32 (rev. 2015) – EN 55032 (rev. 2012/AC:2013) – EN 55032 (rev. 2015) – EN61000-3-2 (rev. 2014) – EN61000-3-3 (rev. 2013) – KN61000-3-2 – KN61000-3-3 – AS/NZS CISPR 32 Class B (rev. 2015) – 47 CFR FCC Part 15B – ICES-003 (rev. 2016 Issue 6, Class B) – VCCI-CISPR 32 – CNS (rev. 13438) – KN-32 – QCVN 118:2018/BTTTT • Immunity: – CISPR 24 (rev. 2010) – EN 55024 + AMD 1(rev. 2010) – EN 55035: 2017 – KN35 • Emissions and immunity: – EN 301 489-1 (v2.1.1 2017-02) – EN 301 489-17 (v3.1.1 2017-02) – QCVN (18:2014) – QCVN 112:2017/BTTTT – KN 489-1 – KN 489-17 – EN 60601-1-2:2015 – EN 61000-6-1: 2007 • Radio: – EN 300 328 (v2.1.1) – EN 301 893 (v2.1.1) – AS/NZS 4268 (rev. 2017) – 47 CFR FCC Part 15C, 15.247, 15.407 – RSP-100 – RSS-GEN – RSS-247 – China regulations SRRC – LP0002 (rev 2018.1.10) – Japan Std. 33a, Std. 66, and Std. 71 • RF safety: – EN 50385 (rev. Aug 2002) – ARPANSA – AS/NZS 2772 (rev. 2016) – EN 62209-1 (rev. 2016) – EN 62209-2 (rev. 2010) – 47 CFR Part 1.1310 and 2.1091 – RSS-102 • IEEE standards: – IEEE 802.3 – IEEE 802.3ab – IEEE 802.3af/at – IEEE 802.11a/b/g/n/ac/ax – IEEE 802.11h, 802.11d • Security: – 802.11i, Wi-Fi Protected Access 2 (WPA2), WPA3 – 802.1X – Advanced Encryption Standard (AES) • Extensible Authentication Protocol (EAP) types: – EAP-Transport Layer Security (TLS) – EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol (MSCHAP) v2 – Protected EAP (PEAP) v0 or EAP-MSCHAP v2 – EAP-Flexible Authentication via Secure Tunneling (EAP-FAST) – PEAP v1 or EAP-Generic Token Card (GTC) – EAP-Subscriber Identity Module (SIM) |
Cisco AP C9130AX Series provides these features:
• Wi-Fi 6 certified, supporting 802.11ax on both 2.4-GHz and 5-GHz bands
• Up to four Wi-Fi radios: 5GHz flexible radio (single 8×8 or dual 4×4), 2.4GHz (4×4) and Cisco RF ASIC
• OFDMA and MU-MIMO
• Multigigabit support
• Internal and external antenna
Future feature support:
• IoT ready (BLE, other 802.15.4 protocols** like Zigbee)
** – Supported in future software releases